The Fundamentals of Plumbing Knowledge When Installing a Bathtub
The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Blog Article
Do you find yourself looking for insight around A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't specifically rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably tough project. If the old tub is readily available, the job can move quickly; if you have to open a wall to eliminate the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will require a helper to leave the old bathtub and embeded in the brand-new one. Ensure you have actually certified on your own for the job as well as fit trying it. Instead of working with a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might require a professional plumber to make tube links.
This short article will certainly assist you mount a new tub in your restroom if you have already purchased a new tub and don't need to change the arrangement of your previous supply of water pipelines.
Your tools and product checklist should comprise the following:
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to avoid pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its final placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a towel all set for the continuing to be water that will originate from the pipes. When the supply pipes have actually been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, place the tub in the needed placement. The wood boards are valuable in uniformly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the bath tub until the level reviews degree.
To install taps, fit the bottom of the furthest flexible faucet port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and inspect all joints and brand-new pipework for leakages and tighten them if required. Fill up the tub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, deal with the bath paneling as described in the producer's instruction manual. Tiling and also securing around the bathtub should wait until the tub has been utilized at least once as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place between the tap as well as the sink. Safeguard the faucet in place with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former type must be connected to the faucet finishes initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture a rigid seal, triggering the water to pass through the wall between the bath and the tiling, causing complications with wetness and also possible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can break rather early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the marketplace. It is advisable to fit the floor tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our part about How to Install a Bathtub. Thank you for taking time to browse our short article. Kindly set aside a second to share this entry if you enjoyed it. Thanks a lot for your time. Kindly come visit our blog back soon.
Navigate plumbing issues professionally. Report this page